IOTA Engineering, 120Vdc to 12Vdc, 90A Converter/Charger, DLS-12V-90A/120V

Description: Normal 0 false false false EN-US X-NONE X-NONE Free shipping is for the contiguous United States only.The images shown are for illustration purposes only and may not be an exact representation of the product.Please Note:All my items ship directly from my suppliers, and the warrantee starts when you receive the item. IOTA ENGINEERING LLC DLS90AC Battery Charger Power Converter The DLS series power converter/battery charger from IOTA Engineering converts 120 volts nominal A.C. to 13.6 volts D.C. As a power supply, its tightly controlled regulation allows the user to operate any 12 volt nominal D.C. load up to the converter’s rated output current. As a battery charger, the converter will maintain the battery, delivering its full-rated current when the battery capacity falls sufficiently low. The voltage is set to deliver its maximum current for the necessary period of time that minimizes undue stress to the battery caused by heating of its cells. This helps to ensure the longest possible life of the battery. Over time, as the battery nears its full capacity, the converter will float-charge the battery to prevent self-discharge of its cells.The DLS-90 features a Dual Voltage Jack which allows switching from a long-term float voltage of 13.6vdc to a 14.2vdc rapid charge by simply inserting the dual voltage plug (included) into the jack.The DLS-90 is also available with an IQ Smart-Controller already integrated into the unit, providing "smart-charging" capability and increasing the performance of the DLS.Features include:Switch-Mode TechnologyLow and Transient AC Line Voltage ProtectionExceptionally Clean DC OutputReverse Polarity ProtectionProportional Fan ControlModel SpecificationsDLS-90DLS-75DLS-55DLS-45DLS-30DLS-15DC Output Voltage (No Load) approx.13.6 V (DC)13.6 V (DC)13.6 V (DC)13.6 V (DC)13.6 V (DC)13.6 V (DC)Output Voltage Tolerance (No Load)+ or - .7%+ or - .7%+ or - .7%+ or - .7%+ or - .7%+ or - .7%Output Amperage, Max Continuous90 Amps75 Amps55 Amps45 Amps30 Amps15 AmpsOutput Voltage (Full Load) approx.>13.4 V (DC)>13.4 V (DC)>13.4 V (DC)>13.4 V (DC)>13.4 V (DC)>13.4 V (DC)Maximum Power Output, Continuous1210 Watts1000 Watts740 Watts600 Watts400 Watts200 WattsRipple and Noise<150 mV rms<100 mV rms<50 mV rms<50 mV rms<50 mV rms<50 mV rmsInput Voltage Range108 - 132 AC108 - 132 AC108 - 132 AC108 - 132 AC108 - 132 AC108 - 132 ACInput Voltage Frequency47 - 6347 - 6347 - 6347 - 6347 - 6347 - 63Maximum AC Current @ 108Vac21 Amps17 Amps13 Amps11 Amps7 Amps3.5 AmpsTypical Efficiency>80%>80%>80%>80%>80%>80%Max Inrush Current, Single Cycle40 Amps22 Amps20 Amps20 Amps16 Amps8 AmpsShort Circuit ProtectionYesYesYesYesYesYesOverload Protection>100%>100%>100%>100%>100%>100%Line Regulation100 mV rms100 mV rms100 mV rms100 mV rms100 mV rms100 mV rmsLoad Regulation<1.5%<1.5%<1.5%<1.5%<1%<1%Fan ControlPROPORTIONALPROPORTIONALPROPORTIONALPROPORTIONALPROPORTIONALNAThermal ProtectionYESYESYESYESYESYESWorking Temperature Range0 - 40C0 - 40C0 - 40C0 - 40C0 - 40C0 - 40CStorage Temperature-20 to 80C-20 to 80C-20 to 80C-20 to 80C-20 to 80C-20 to 80CWithstand Voltage1240V @ leads1240V @ leads1240V @ leads1240V @ leads1240V @ leads1240V @ leadsDimensions10" x 6.5" x 3.5"10" x 6.5" x 3.5"7" x 6.5" x 3.5"7" x 6.5" x 3.5"7" x 6.5" x 3.5"7" x 6.5" x 3.5"Weight7.8 lbs7.8 lbs5.5 lbs5.5 lbs5.5 lbs4.0 lbsPROTECTION FEATURESThe DLS series power converter/battery charger is designed with high quality components to help ensure years of continuous use. The DLS series is protected by multiple protection features for a long, trouble-free life. 1) Reverse Battery Polarity Protection. 2) Brown-Out Input Protection. 3) Over-Current Protection - cycle by cycle peak limiting as well as rated current limiting to maximize the life of the converter. 4) Over-Temperature Protection. In addition, it is designed with a unique “proportional” fan control circuit. Fan speed is directly proportional to the converter’s internal ambient temperature. This enables the fan to turn on and off very slowly, minimizing unwanted fan-starting noise.WARRANTYThe DLS series power converter/battery charger is warranted from defects in materials or workmanship for two years from date of retail purchase, and limits the remedies to repair or replacement. This warranty is valid only in the continental United States and Canada.INSTALLATION GUIDELINESThere are no components within the DLS unit that, in their normal operation, produce arcs or sparks. However, all electronic devices have some potential for generating sparks in the event of failure. Therefore, never install this device in the same compartment with flammable items such as gasoline or batteries.MOUNTING LOCATIONThe DLS battery charger/power supply can be mounted in any position within an enclosed or interior compartment. Provide sufficient air space to allow unrestricted airflow in and around the unit.DLS INSTALLATIONDisconnect the positive side of the battery before installation. Connect the positive (red) and negative (black) terminal lugs to battery or load. Always use the proper size wire based on the amperage of the converter and the battery. When connecting to a battery, a breaker should be installed within 18” of the battery, connecting the battery positive to the line side of the breaker, and the DLS to the load side. Connect “Chassis Bonding Lug” on the DLS to vehicle chassis or other grounding source.120 VOLT A.C. INPUTPlug the DLS A.C. input cord into a 120 volt 3 wire grounded source. See chart for maximum current draw and required input voltages.REVERSE POLARITY FUSESThe DLS Battery Charger/Power Supply is protected against reverse polarity on the DC output. If a battery or the DLS is hooked up incorrectly, the fuses will blow and can be easily replaced. Always use the same size and style fuse that came with the converter. To change the fuses, use a screwdriver to loosen the screws and remove the fuses. Always replace the fuses with the same type and rating. After inserting the new fuses, tighten the screws firmly. DO NOT OVERTIGHTEN.CHARGE CONTROLLER OPTIONSCharge Controller Options are designed for DLS units that DO NOT have the IQ SMART CONTROL FEATURE internally integrated. It is not necessary to utilize the Dual Voltage Jack or External IQ Controller for IQ-integrated DLS units. TWO-STEP VOLTAGE JACKThe two-step voltage jack (located on the top of the DLS on the fan-end of the unit) allows switching from a long-term float voltage of 13.6vdc up to 14.2vdc. When the included dual voltage plug is inserted in the jack, the voltage rises to 14.2vdc for occasional fast charging. When the plug is removed, the voltage drops to 13.6vdc to reduce battery water loss. WARNING: To avoid battery damage, remove the Dual Voltage Plug when quick-charging is complete.IQ SMART CHARGERDLS power converters/chargers are designed to accommodate the IQ smart charge controller. The microprocessor- controlled charger turns the DLS charger into an “automatic” 3-stage “smart charger,” giving the user the benefit of Bulk, Absorption, and Float stage charging. This increases the charging capacity of the DLS charger, decreases charge times and insures proper and safe battery charging without over-charging. The IQ controller inserts into the dual voltage jack on the DLS. Everyone’s Solar Profile. I recently sold my successful solar company that I created around 1992 in the state of Maine. My solar experience is in site surveys, design, installations, and maintenance of 500 plus clients, specializing in off grid homes, and owning my own off grid home. Solar is part of my life and the bonus of meeting so many different client’s needs, remains my quest to see more people enjoy their home with solar. I have taken advantage of my suppliers for the last 25 years to give you the best price I possibly can. If you don’t find what you need on my site, please tell me what you need, and I will do my best to get it for you. If you are new to solar and need help, feel free to reach out to me. I will be more than happy to design a system for your needs. I normally ship within two days of receiving payment, however if your item is not readily available I will inform you immediately and make the necessary required changes. Sincerely John Myatt Contact me at two, zero, seven, - two-eight-zero, - zero, six, two, five. Do to the supply chain issues and backorders please message me to make sure I have your item in stock!

Price: 333.8 USD

Location: New Holland, Pennsylvania

End Time: 2024-09-22T17:05:47.000Z

Shipping Cost: 0 USD